Samson 3730-4 Скачать руководство пользователя страница 25

Страница: 25 / 100

Fault/diagnostic alarm

Value (hex) Status alarm acc. to

Profile 3.01

Function activated

Initialization active

0x80

GOOD_NON_SPECIFIC

Diagnostic function activated

0x80

GOOD_NON_SPECIFIC

5.4

Status alarms according to Profile 3.01 Condensed Status

Fault/diagnostic alarm

Default setting acc. to Pro-

file 3.01 Condensed Status

Classified

Diagnosis

Yes

Operational error

Device not initialized

0x24 BAD_MAINT_ALARM

•

DIA_INIT_ERR

Solenoid valve active

0x80 GOOD_NON_SPECIFIC

•

–

Total valve travel exceeded

0xA4 GOOD_MAINT_REQ

•

DIA_MAINTENANCE

Control loop error

0xA4 GOOD_MAINT_REQ

•

DIA_MAINTENANCE

Zero point error

0xA4 GOOD_MAINT_REQ

•

DIA_ZERO_ERR

Autocorrection

0x80 GOOD_NON_SPECIFIC

•

DIA_MAINTENANCE

DIA_MEM_CHECKSUM

Fatal error

0x24 BAD_MAINT_ALARM

•

DIA_HW_ELECTR

Extended diagnostics available

0x80 GOOD_NON_SPECIFIC

•

DIA_MAINTENANCE

EXTENSION_AVAILABLE

No emergency mode

0xA4 GOOD_MAINT_REQ

•

DIA_MEM_CHECKSUM

Temperature < –40 °C

0x80 GOOD_NON_SPECIFIC

•

–

Temperature > 80 °C

0x80 GOOD_NON_SPECIFIC

•

–

Initialization error

x > range

0xA4 GOOD_MAINT_REQ

•

DIA_INIT_ERR

Delta x < range

0xA4 GOOD_MAINT_REQ

•

DIA_INIT_ERR

Incorrect attachment

(mechanics/pneumatics)

0xA4 GOOD_MAINT_REQ

•

DIA_INIT_ERR

Initialization time exceeded

0xA4 GOOD_MAINT_REQ

•

DIA_INIT_ERR

Solenoid valve initialization

0xA4 GOOD_MAINT_REQ

•

DIA_INIT_ERR

Transit time too short

0xA4 GOOD_MAINT_REQ

•

DIA_INIT_ERR

Pin position

0xA4 GOOD_MAINT_REQ

•

DIA_INIT_ERR

KH 8384-4 EN

Measured value status and valve diagnostics

Содержание 3730-4





































































































Результаты поиска

Содержание 3730-4

Отзывы:

Бренды по названию

Популярные бренды

Samson 3730-4, Руководство по настройке

Результаты поиска

Содержание 3730-4

Отзывы:

Бренды по названию

Популярные бренды