Samson 3730-4 Скачать руководство пользователя страница 74

Страница: 74 / 100

SETP_CUTOFF_INC (119)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Final position w > (Code 15)
If the reference variable exceeds the entered value, the valve moves towards the final position which

corresponds to 100 % reference variable.

Electropneumatic actuators are completely filled with air or vented (depending on the fail-safe position).
• [125.0 %]

ST_REV (81)

Storage class: – · Read capability (r)

Revision level of static data

STRATEGY (83)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Grouping to allow faster processing of blocks
• [0]
Blocks are grouped by entering the same value in the STRATEGY parameter of each block.

TAG_DESC (82)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Used to enter a user-selected text to identify and assign blocks.
• Max. 32 characters, [no text]

TARGET_MODE (85)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Target mode
• [8] · AUTO (automatic mode)
• 16 · MAN (manual mode)
• 128 · O/S (out of service)

TOT_VALVE_TRAV_LIM (126)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Limit value for the total valve travel (Code 24)
• [1000000.0]

TOTAL_VALVE_TRAVEL (125)

Storage class: – · Read capability (r)

Total valve travel: Totaled double valve travel (Code 23)

KH 8384-4 EN

AO Transducer Block, Slot 1

· Profile-specific parameters

Содержание 3730-4





































































































Результаты поиска

Содержание 3730-4

Отзывы:

Бренды по названию

Популярные бренды

Samson 3730-4, Руководство по настройке

Результаты поиска

Содержание 3730-4

Отзывы:

Бренды по названию

Популярные бренды