manualshive.com logo in svg

Samson 3730-4, Руководство по настройке

Поделиться
Скачать
Samson 3730-4 Скачать руководство пользователя страница 86

• PST_CANCEL_COND_ACTIV_MAX_TIME (activation 'Max. breakaway time')
• PST_CANCEL_COND_MAX_BREAK_TIME (max. breakaway time)
• PST_CANCEL_COND_ACTIVE_TIME_REACH (activation 'Allowed time to reach PST target')
• PST_CANCEL_COND_TIME_REACH (allowed time to reach PST target)

PST_DISPLAY (218)

Storage class: –  ·  Read capability (r)

Information on partial stroke test (PST)
• AUTOSTART_READ (auto test time)
• PROGRESS_FLAG (progress flag)
• DELTA_Y_MON_REF_VAL (delta y monitoring reference value)
• DELTA_Y_MON_REP_VAL (delta y monitoring repetition value)
• STATUS_PST (status of PST test)
• NUMBER_OF_TESTS (number of PST tests)
• RECOMMEND_SCAN_RATE (recommended scan rate)
• DURATION_OF_TEST (test duration)
• TESTMODE_ACTUAL (current test mode)
• TEST_INFO (test information)

PST_SETTINGS (216)

Storage class: S  ·  Read/write capability (r/w)  ·  Supported modes: ALL

Settings for partial stroke test (PST)
• PST_SETTINGS_AUTOSTART (auto test time)
• PST_SETTINGS_STEP_START (step start)
• PST_SETTINGS_STEP_END (step end)
• PST_SETTINGS_LIMIT_STEP_RESPONSE (tolerance limit of step response)
• PST_SETTINGS_ACTIVATION_RAMP_FUN (activation of ramp function)
• PST_SETTINGS_RAMP_TIME_RISING (ramp time, rising)
• PST_SETTINGS_RAMP_FALLING (ramp time, falling)
• PST_SETTINGS_SETTLING_TIME (settling time before test starts)
• PST_SETTINGS_DELAY_TI_AFTER_STEP (delay time after step)
• PST_SETTINGS_SCAN_RATE (scan time)
• PST_SETTINGS_STEP_RESPONSE (number of step reponses)

86

KH 8384-4 EN

AO Transducer Block, Slot 1

· Manufacturer-specific parameters

Содержание 3730-4





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды