Samson 3730-4 Скачать руководство пользователя

Страница: 17 / 100

Measured value status and valve diagnostics

5.1

Extended valve diagnostics – EXPERTplus

The Type 3730-4 Positioner includes integrated diagnostic functions. According to the

Profibus Profile 3.01 and the 'Condensed status and diagnostic messages' extension, the

generated alarms can be classified and summarized (see section 5.5, page 29).
The EXPERTplus extended diagnostics provides the following in-service monitoring and

out-of-service tests to provide significant statements on the condition of the entire control

valve.

Statistical information (in-service monitoring)

Data logger

Histograms

Cycle counter

Valve end position trend

Drive signal diagram

Hysteresis test

Tests (out-of-service tests)

Drive signal diagram over the full range of the valve

Hysteresis test diagram over the full range of the valve

Static characteristic

Partial stroke test

The diagnostic tests are completely integrated into the positioner. The PROFIBUS-PA protocol

allows parameters to be entered and test results to be read. The graph readings depend on

the process control system used.

Further status alarms are generated from the extensive information compiled during the diag-

nostic tests of EXPERTplus which provide the user with information covering the entire control

valve.
The required reference graphs are automatically plotted after initialization and saved in the

positioner if the plotting is activated with Code 48 - h0 in EXPERTplus.

KH 8384-4 EN

Measured value status and valve diagnostics

Содержание 3730-4





































































































Результаты поиска

Содержание 3730-4

Отзывы:

Похожие инструкции для 3730-4

Бренды по названию

Популярные бренды

Samson 3730-4, Руководство по настройке

Результаты поиска

Содержание 3730-4

Отзывы:

Похожие инструкции для 3730-4

Бренды по названию

Популярные бренды