Rural King RK19 Hydrostatic Скачать руководство пользователя страница 92

Страница: 92 / 156

5 - 9

Maintenance and service

435

(3) Oil specification

Gear oil SAE 90W
(API GL- grade or higher)

replacing transMissiOn

fluid filter cartridge

①

The HST oil filter is located under

the floor.

②

Remove the hydraulic oil filter

element by turning it counterclock-

wise with a wrench.

③

Apply a thin film of oil to the O-ring

of a new cartridge and install the

new cartridge by tightening it with

a hand. When its packing touches

the sealing surface, turn it approx.

/ turns further with a wrench.

④

Add hydraulic oil to the specified level.

⑤

Check the oil level with the dipstick

again. If still insufficient, add more.

►

If oil gets on your skin, it can ir-

ritate the skin and cause a skin

condition. Make sure to clean

your skin with soap and water

or hand cleaner thoroughly.
Make sure to cool down the

engine sufficiently before drain

ing oil. Oil is very hot and can

cause a burn if changing oil

right after the engine is stopped.

•

cautiOn

HST filter

5. replacing filter and cartridge

transMissiOn strainer

cleaning

①

When changing transmission

fluid, clean with diesel fuel.

②

Unscrew the filter body support

bolt from the right lower section

of the rear transmission case

and gently pull the filter with pli

ers to remove it.

►

T19O509A

T19O510B

RK19-영문-05(마).indd 9

2017-05-18 오후 6:35:21

Содержание RK19 Hydrostatic





























































































































































Результаты поиска

Содержание RK19 Hydrostatic

Отзывы:

Rural King RK19 Hydrostatic, Руководство оператора, Страница: 92 / 156

Результаты поиска

Содержание RK19 Hydrostatic

Отзывы: