Rural King RK19 Hydrostatic Скачать руководство пользователя страница 62

Страница: 62 / 156

2 - 1

DESCRIPTION OF TRACTOR CONTROLS

• REAR PTO

T h e t r a c t o r h a s o n e s p e e d

PTO(540rpm). Use the PTO lever

to engage. The PTO switch must be

OFF before PTO is engaged.
1. Decrease engine speed to near

idle.

2. Make sure that PTO switch is

OFF.

3. Engage rear PTO using the PTO

lever.

4. Turn on the PTO switch.
5. Increase engine speed to desired

speed.

REAR PTO SPEED

540 RPM

• MID PTO

The speed of mid PTO is 2.500 rpm.

Use the PTO lever to engage. The

PTO switch must be OFF before

PTO is engaged.
1. Decrease engine speed to near

idle.

2. Make sure that PTO switch is

OFF.

3. Engage mid PTO using the PTO

lever.

4. If rear PTO is needed to engage,

shift the PTO lever to correct po-

sition.

Mid

T19O128B

N
Mid+Rear
N
Rear

T19O142B

T19O130A

MID PTO SHAFT

RK19-영문-02(나).indd 19

2017-05-18 오후 6:22:53

Содержание RK19 Hydrostatic





























































































































































Результаты поиска

Содержание RK19 Hydrostatic

Отзывы:

Rural King RK19 Hydrostatic, Руководство оператора, Страница: 62 / 156

Результаты поиска

Содержание RK19 Hydrostatic

Отзывы: