Rural King RK19 Hydrostatic Скачать руководство пользователя страница 14

Страница: 14 / 156

- 1

SAFeTY PReCAUTIONS

T72O208A

Do not allow riders on the tractor.
Riders on tractor are subject to in-

jury such as being stuck by foreign

objects and being thrown off of the

tractor.

KeeP RIDeRS OFF TRACTOR

T72O209A

Handle fuel with care; it is highly

flammable. Do not refuel the tractor

while smoking or near open flame

or sparks.
Always stop engine before refueling

tractors.
Always keep your tractor clean of

accumulated grease, and debris. Al-

ways clean up spilled fuel.

HANDLe FUeL SAFeLY AVOID FIReS

T72O210A

Entanglement in rotating shaft can

cause serious injury or death.
Keep PTO shield in place at all

times.

Wear close fitting clothing. Stop the

engine and be sure PTO drive is

stopped before making adjustments,

connections, or cleaning out PTO

driven equipment.

STAY CLeAR OF ROTATING SHAFTS

RK19-영문-01A(안).indd 13

2017-05-19 오전 9:41:23

Содержание RK19 Hydrostatic





























































































































































Результаты поиска

Содержание RK19 Hydrostatic

Отзывы:

Rural King RK19 Hydrostatic, Руководство оператора, Страница: 14 / 156

Результаты поиска

Содержание RK19 Hydrostatic

Отзывы: