Rural King RK19 Hydrostatic Скачать руководство пользователя страница 109

Страница: 109 / 156

6 -

Storage and diSpoSal

1. tractor Storage

daily Storage

(1) Store the tractor after cleaning it.

Especially, clean it thoroughly af-

ter harrowing or working in a wet

field.

() Make sure to lower an imple-

ment.

(3) Store the tractor indoors if possi

ble.

(4) If storing the tractor outside, cov

er it.

(5) For better startability, it is recom-

mended to remove the battery

from the tractor and keep it in

doors in winter.

(6) If the outside temperature is be

low

32℉(

℃)

, add antifreeze or

drain coolant completely to pre

vent the engine from freezing

and bursting.

(7)

Remove the key and store it

separately.

►

long-term Storage

Clean the tractor thoroughly and

store it as follows:
(1) Change engine oil with new oil

and run the engine for 5 min

utes to distribute oil to each part

evenly.

(2) Drain coolant from the radiator.

Then, make a label indicating

"No Coolant" and fix it onto the

steering wheel.

If antifreeze is already added, it

is not necessary to drain coolant.

(3) Add oil, fluid and fuel to each

part according to the mainte

nance chart.

(4) Apply a thin film of grease of oil

to body parts that are apt to rust.

(5) Check each bolt and nut for

looseness and tighten any loose

bolt and nut.

(6) Set the tire inflation pressure a

little higher than the specifica-

tion.

►

(7) Remove a weight. Detach or

lower an implement.

(8) Chock the rear wheels.

(9) Remove the battery from the

tractor or turn off its switch to

cut power connection.

(10) Place wood blocks under the

tires to protect them.

(11) Charge the battery every 2

months during long-term stor

age.

(12) Store it in a dry place to avoid

rain or snow and cover the

body.

RK19-영문-06(바).indd 2

2017-05-19 오전 9:47:27

Содержание RK19 Hydrostatic





























































































































































Результаты поиска

Содержание RK19 Hydrostatic

Отзывы:

Rural King RK19 Hydrostatic, Руководство оператора, Страница: 109 / 156

Результаты поиска

Содержание RK19 Hydrostatic

Отзывы: