Rural King RK19 Hydrostatic Скачать руководство пользователя страница 64

Страница: 64 / 156

2 - 21

DESCRIPTION OF TRACTOR CONTROLS

OPERATING TIPS FOR POWER

STEERING WHEEL

(1) Operate the power steering

wheel only while the engine is

running. You may feel the steer-

ing wheel heavier with a low en-

gine speed.

(2) When an implement, such as a

loader, is attached to the front,

the steering wheel may be felt

heavy with the tractor stopped.

If so, operate the steering wheel

while driving the tractor at a low

speed.

(3) When the steering wheel is

completely turned to one end,

the safety valve is activated to

output the audible signal (relief

sound). When this sounds, avoid

using the steering wheel (O.K.

only for a short time). Also, never

turn the steering wheel com-

pletely continuously.

►

(1) Loader lever operating directions

- Boom down (D)

- Boom up (C)

- Bucket up (B)

- Bucket down (A)

Do not operate the boom cylin-

der and bucket cylinder at the

same time. A loader may mal-

function due to insufficient oil

flow.

•

NOTE

T19O133A

(4) Turning the steering wheel to

its end unnecessarily (with the

tractor stopped) can wear tires

rapidly.

(5) In winter, warm up the engine

sufficiently before use.

(6) When repairing components,

such as a pipe, make sure that

no foreign material enters the

system.

(7) The steering wheel can be op-

erated with a small amount of

force. Therefore, operate it with

care and keep your hands on it

at all times.

Releasing the steering wheel

during driving can result in a

collision and rollover. Never re-

lease the steering wheel during

driving.

•

WARNING

Loader Lever

RK19-영문-02(나).indd 21

2017-05-18 오후 6:22:57

Содержание RK19 Hydrostatic





























































































































































Результаты поиска

Содержание RK19 Hydrostatic

Отзывы:

Rural King RK19 Hydrostatic, Руководство оператора, Страница: 64 / 156

Результаты поиска

Содержание RK19 Hydrostatic

Отзывы: