Rural King RK19 Hydrostatic Скачать руководство пользователя страница 75

Страница: 75 / 156

3 -

OPERATION

8. CAuTIONs fOR dRIvINg INTO / OuT Of fIEld

(1) Check that the left and right brake pedals are connected.
(2) It is dangerous to drive into/out of a field if the field is deep from its bank.

Use ramps.

(3) Move in the perpendicular direction to the bank.
(4) When driving out of the field, lower the implement so that the front wheels

cannot be lifted.

(5) It is recommended to drive into a field backward to utilize full power.

Be careful to keep the tractor's balance when working on a slope. The

tractor may become out of balance and roll over.
It is very dangerous to ride a person as a front weight.

•

wARNINg

☞

For detailed precautions, refer to the page 0-23.

(1) When loading the tractor onto a truck, drive backward.
(2) Be extra careful when using ramps.
(3) If the engine stops on ramps, depress the brake pedals immediately and

release them slowly to move onto the ground. Then, start the engine again

to climb the ramps again.

9. lOAdINg TO / uNlOAdINg fROm TRuCk

RK19-영문-03(다).indd 6

2017-05-19 오전 9:45:16

Содержание RK19 Hydrostatic





























































































































































Результаты поиска

Содержание RK19 Hydrostatic

Отзывы:

Rural King RK19 Hydrostatic, Руководство оператора, Страница: 75 / 156

Результаты поиска

Содержание RK19 Hydrostatic

Отзывы: