Rural King RK19 Hydrostatic Скачать руководство пользователя страница 13

Страница: 13 / 156

- 12

SAFeTY PReCAUTIONS

after for any evidence of damage,

wear or cracks. In the event of dam-

age or alteration, the ROPS must be

replaced prior to further operation of

the tractor.
The seat belt must be worn during

machine operation when the ma-

chine is equipped with a certified

ROPS.
Failure to do so will reduce or elim-

inate protection for the operator in

the event of a roll over.

T72O206A

Do not drive where the tractor could

slip or tip.
Stay alert for holes and rocks in the

terrain, and other hidden hazards.
Slow down before you make a sharp

turn.
Driving forward out of a ditch or

mired condition could cause trac-

tor to tip over backward. Back out of

these situations if possible.

PReCAUTION TO AVOID TIPPING

T72O207A

Before working on the tractor;
Lower all equipment to the ground.
Stop the engine and remove the

key.

PARK TRACTOR SAFeLY

RK19-영문-01A(안).indd 12

2017-05-19 오전 9:41:22

Содержание RK19 Hydrostatic





























































































































































Результаты поиска

Содержание RK19 Hydrostatic

Отзывы:

Rural King RK19 Hydrostatic, Руководство оператора, Страница: 13 / 156

Результаты поиска

Содержание RK19 Hydrostatic

Отзывы: