Rural King RK19 Hydrostatic Скачать руководство пользователя

Страница: 69 / 156

2 - 2

DESCRIPTION OF TRACTOR CONTROLS

Towing hitch

SAFETy FRAME ROPS

The safety frame is intended to reduce

damage of an accident in case of a roll-

over, so it cannot prevent an accident.
Always have the safety frame installed

securely for driving to ensure your

safety unless going under an area

with a low ceiling such as a garage.

►

ROPS

TOWING HITCH

Install only an implement applicable

to this tractor.

►

Make sure to use the towing

hitch for towing to avoid roll-

over. Never tow anything by

connecting a rope to the top link

bracket, axle or safety frame.
When using a rotavator that

draws power through the uni-

versal joint from the PTO shaft,

remove the towing hitch from

the tractor. Otherwise, the uni-

versal joint hits and damages

the towing hitch, leading to an

accident.

•

WARNING

If a rollover accident occurs

without the safety frame, the

frame cannot protect the driver,

leading to a severe injury or

even death. Never drive with

the safety frame detached.

•

WARNING

T19O139A

R19O203A

RK19-영문-02(나).indd 26

2017-05-18 오후 6:23:01

Содержание RK19 Hydrostatic





























































































































































Результаты поиска

Содержание RK19 Hydrostatic

Отзывы:

Похожие инструкции для RK19 Hydrostatic

Бренды по названию

Популярные бренды

Rural King RK19 Hydrostatic, Руководство оператора

Результаты поиска

Содержание RK19 Hydrostatic

Отзывы:

Похожие инструкции для RK19 Hydrostatic

Бренды по названию

Популярные бренды