Rural King RK19 Hydrostatic Скачать руководство пользователя

Страница: 27 / 156

- 2

SAFeTY PReCAUTIONS

10. Pull only from the draw bar or

the lower link drawbar in the

down position. Use only a draw-

bar pin that locks in place. Pull-

ing from the tractor rear axle

carriers or any point above the

rear axle may cause the tractor’

s front end to lift.

11. If the front end of the tractor

tends to rise when heavy imple-

ments are attached to the three-

point linkage, install front end

or front wheel weights. Do not

operate the tractor with a light

front end.

12. Always use hydraulic posi-

tion control lever when attach-

ing equipments/implement and

when transporting equipment.

Be sure that the hydraulic cou-

plers are properly mounted and

will disconnect safely in case of

accidental detachment of imple-

ment.

13. Do not leave equipment/imple-

ment in the raised position.

14. Use the flasher/ Turn signal

lights and Slow Moving Vehi-

cle (SMV) signs when driving

on public roads during both day

and night time, unless prohibit-

ed by law.

15. Dim tractor lights when meet-

ing a vehicle at night. Be sure

the lights are adjusted to pre-

vent the blinding on the eyes of

coming vehicle operator.

<DRIVING THe TRACTOR>

1. Watch where you are going es-

pecially at row ends, on roads,

around trees and low hanging

obstacles.

2. To avoid upsets, drive the trac-

tor with care and at speeds

compatible with safety, espe-

cially when operating over

rough ground, crossing ditches

or slopes, and when turning at

corners.

3. Lock the tractor brake pedals to-

gether when transporting on

roads to provide proper wheel

braking.

4. Keep the tractor in the same gear

when going downhill as used

when going uphill. Do not coast

or free wheel down hills.

5. Any towed vehicle and/or trail-

er whose total weight exceeds

that of the towing tractor, must be

equipped with its own brakes for

safe operation.

6. When the tractor is stuck or tires

are frozen to the ground, back

out to prevent upset.

7. Always check overhead clear-

ance, especially when transport-

ing the tractor.

RK19-영문-01A(안).indd 26

2017-05-19 오전 9:41:33

Содержание RK19 Hydrostatic





























































































































































Результаты поиска

Содержание RK19 Hydrostatic

Отзывы:

Похожие инструкции для RK19 Hydrostatic

Бренды по названию

Популярные бренды

Rural King RK19 Hydrostatic, Руководство оператора

Результаты поиска

Содержание RK19 Hydrostatic

Отзывы:

Похожие инструкции для RK19 Hydrostatic

Бренды по названию

Популярные бренды