Rural King RK19 Hydrostatic Скачать руководство пользователя страница 74

Страница: 74 / 156

OPERATION

3 - 5

7. dRIvINg ON slOPE

sTARTINg Off ON sTEEP slOPE

①

Depress the brake pedals.

②

Place each shift lever in the low

speed position.

③

Set the engine at the mid speed

with the throttle lever.

④

Release the brake pedal slowly

at the same time.

►

After parking, make sure to ap

ply the parking brake.
Avoid parking on a slope if pos

sible. If it is absolutely neces-

sary to park on a slope, chock

the rear wheels.

•

wARNINg

⑥

Remove the key from the switch

after parking vehicle.

☞

Refer to the page 2-13 for opera

tion of the parking brake.

TIPs fOR dRIvINg ON slOPE

(1) Set the main shift lever in the

low speed position on a slope

to prevent the engine from stop

ping.

(2) Keep the driving speed low on a

downhill road.

►

When the needle on the coolant

temperature gauge is pointing

at 'H,' the engine is overheated.

If running the engine under

this condition continuously, the

engine parts can be severely

damaged. Make sure to take an

appropriate action immediately.

•

NOTE

RK19-영문-03(다).indd 5

2017-05-19 오전 9:45:15

Содержание RK19 Hydrostatic





























































































































































Результаты поиска

Содержание RK19 Hydrostatic

Отзывы:

Rural King RK19 Hydrostatic, Руководство оператора, Страница: 74 / 156

Результаты поиска

Содержание RK19 Hydrostatic

Отзывы: