Rural King RK19 Hydrostatic Скачать руководство пользователя

Страница: 65 / 156

2 - 22

DESCRIPTION OF TRACTOR CONTROLS

IMPLEMENT LIFT CONTROL

SySTEM

(1) Position lever
This lever is used to lift and lower

an implement to a certain working

height freely and maintain it.

<Operation>

「

Lifting implement

」

Pull the lever back to lift the im-

plement.

「

Lowering implement

」

Push the lever forward to lower

the implement.

►

Position lever

DOWN

When leaving the tractor, make

sure to lower the implement and

stop the engine. Others may

operate one of the controls,

leading to a dangerous situa-

tion.

•

WARNING

T19O134B

HyDRAULIC LOWERING SPEED

CONTROL KNOb

This can be used to adjust the low-

ering speed of the implement.
Adjust the lowering speed according

to the implement type and working

environment.

<Operation>

Rotavator - Slow the lowering

speed.
Plow - Speed up the lowering

speed.

►

•

Hydraulic lowering

speed control knob

T19O135B

RK19-영문-02(나).indd 22

2017-05-18 오후 6:22:58

Содержание RK19 Hydrostatic





























































































































































Результаты поиска

Содержание RK19 Hydrostatic

Отзывы:

Похожие инструкции для RK19 Hydrostatic

Бренды по названию

Популярные бренды

Rural King RK19 Hydrostatic, Руководство оператора

Результаты поиска

Содержание RK19 Hydrostatic

Отзывы:

Похожие инструкции для RK19 Hydrostatic

Бренды по названию

Популярные бренды