Ross Carbonite Black Series, Руководство по эксплуатации, Страница: 53 / 64

custom control, or used when creating a new custom
control.
Table 6: Special Functions
Function Definition
Hold Allows you to place a command in a
custom control that will stop the custom
control at the hold event. You must
press the custom control button again,
or use a GPI trigger, to continue the
custom control.
Pause Allows you to place a command in a
custom control that will stop a custom
control at the pause event. The length
of the pause is set when the pause is
inserted. When holding the INSERT
button, pauses are shown as P x , where
x is the length of the pause in frames.
Loop Allows you to have a custom control run
continuously until stopped, or a Cancel/
Cancel All custom control command is
executed from another custom control.
GPO Allows you to trigger a pre-selected
GPI output using a custom control.
The specific GPI output is set when the
GPO command is inserted.
CutKey Cut Key Allows you create a custom control that
will cut keys on or off. The specific key
and whether the key is cut on or off
is set when the key cut command is
inserted.
TrnKey Trans Key Allows you to create a custom control
that will transition keys on or off. The
specific key and whether the key is
transitioned on or off is set when the
key transition command is inserted.
IncKey Include
Key
Allows you to create a custom control
that will include a key with the next
transition to take the key on-air, or off-
air. The specific key and whether it
should go on-air, or off-air is set when
the include key command is inserted.
Resume Allows you to resume a particular
custom control that is at a hold. The
specific custom control is set when
the resume is inserted. If the target
custom control is not at a hold event,
the resume command will not start the
target custom control.
Cancel Allows you to stop a particular custom
control. The specific custom control is
set when the cancel is inserted.
CancelAll Cancel
All
Allows you to stop all running custom
controls.
State Allows you to embed the entire state
of the switcher into a custom control. A
state in a custom control behaves just
like a memory.
To Insert a Special Event into a Custom
Control
A special function can be inserted into any existing
custom control, or used when creating a new custom
control.
1.
Start recording or editing your custom control
where you want to insert the special event.
2. Press INSERT . Click Insert Event .
3. Use the INSERT knob to select the event you
want to insert. Click an Event button for the event
you want to insert.
You can also press and hold the
INSERT button
and press the source button on the custom control
bus for the event you want to insert. The event
names are shown on the mnemonics.
•
Hold
— press the
Insert
knob to insert a hold
event Hold — insert a hold event
•
Pause — use the Secs and Frames knobs
to enter the length of the pause event Pause
— enter the length of the pause event in the
Seconds and Frames fields
• Loop
— press the
Loop
knob to loop the
custom control back to the beginning Loop —
loop the custom control back to the beginning
•
GPO — use the Pin knob to select the GPI
output GPO — click a Pin button to select the
GPI output
• CutKey — use the Key knob to select the
key, and the State knob to select whether you
want the key cut on or off Cut Key — click an
ME , Key , and State button to select whether
you want the key cut on or off
• TrnKey
— use the
Key
knob to select the key,
and the State knob to select whether you want
the key transitioned on or off
Trans Key
—
click an ME , Key , and State button to select
whether you want the key transitioned on or
off
•
IncKey — use the Key knob to select the key,
and the State knob to select whether the key
should be transitioned on-air or off-air with
the next transition Include Key — click an
ME
,
Key
, and
State
button to select whether
the key should be transitioned on-air or off-air
with the next transition
• Resume — use the Bank knob to select
the custom control bank, and the CC knob
to select which custom control to resume
Carbonite Black Operation Manual (v14.0) — Custom Controls • 53