Ross Carbonite Black Series, Руководство по эксплуатации, Страница: 27 / 64

2. Use the Layer knob to select where the
MediaWipe will occur.
•
Auto — MediaWipe occurs over highest
number key in the transition.
• Bkgd
— MediaWipe occurs over the
background, but under all keys.
• Key1 — MediaWipe occurs over the
background and key 1, but under remaining
keys.
• Key2 — MediaWipe occurs over the
background and key 2, but under remaining
keys.
•
Key3 — MediaWipe occurs over the
background and key 3, but under key 4.
•
Key4 — MediaWipe occurs over the
background and all keys.
Important:
If a key is above the MediaWipe
layer and included in the MediaWipe
transition, it will cut off-air with the transition.
This is normally covered by the animation
when the layer is above the key.
Transition Limits
The Transition Limit allows you to set the point in a
transition where an auto transition stops. When active,
the point in the transition where the auto transition
will stop is indicated by a flashing segment on the
transition progress bar next to the fader handle. The
auto transition proceeds to this point and stops. The
second auto transition starts from the transition limit
point and goes back to where the first transition started.
Tip: If you turn Limit off when the transition has stopped
at the transition limit point, the next transition starts from
the transition limit point and goes forward to complete the
transition, instead of going back to the start.
To Set Up a Transition Limit
A transition limit is set using the fader of the ME
that you want to set up the transition limit on. The
transition limit is specific to the ME it is set on.
The transition limit is specific to the ME it is set on.
1. Set up the transition you want to perform.
2. Press NEXT until Limit is shown on the menu.
Tip: You can use the same procedure for a MiniME
™
.
3. Move the fader to the position in the transition
where you want to set the transition limit point.
4. Toggle the Limit knob ( On ) to set the transition
limit point.
The segment on the transition progress bar next to
the fader handle flashes, indicating the location of
the transition limit point.
The transition limit is set and active for the ME you
set it on. You can turn transition limit on and off by
toggling the Limit knob while the fader is at either the
top or bottom limit. If the fader is not on a limit when
you toggle the transition limit on, a new transition limit
will be set. Double-press the Limit knob to reset the
transition limit point.
GPI Output Triggers
Each video source can have a GPI output assigned to
it. This GPI can be used to trigger an external device,
such as a video server, to play the cued clip when the
video sources from the video server are taken on-air.
This trigger can be set up to occur automatically any
time the video source is transitioned on-air, or it can be
triggered manually.
An automatic GPI output trigger can be overridden if
required.
Note: The Next Button Secondary Function must be set to
GPO to be able to trigger a GPI output manually using the
NEXT button.
Keep the following in mind when working with GPI
output triggers:
• The
RlClip knob must be set to On to trigger a
GPI output with a transition.
• The Roll Clip
must be set to
On
to trigger a GPI
output with a transition.
• Edge triggered GPI outputs remain triggered for the
configured duration.
• Level triggered GPI outputs toggle between high
and low each time they are triggered.
To Manually Trigger a GPI Output
The GPI must already be set up as a output and the
Next button functionality must be set to GPO before
you can manually trigger it.
1. Press and hold the NEXT button.
While holding the Next button, the mnemonic
buttons light for each GPI output that is currently
triggered.
2.
Press the mnemonic button for the GPI output you
want to trigger. The number of the GPI is shown
on the mnemonics of the buttons.
Carbonite Black Operation Manual (v14.0) — Transitions • 27