Ross Carbonite Black Series, Руководство по эксплуатации, Страница: 35 / 64

10. Use the Type knob to select Global and the
Cntrl and Values knobs to adjust the parameters.
• ChrAng — use this setting to select the fill
color that has been detected as color spill. You
should not have to adjust this setting.
• ReSpil — use the ReSpil , RSCHue , and
RSCSat settings to select a color that is near
the average color of the background/lighting
that needs to be added into those areas of the
fill that contain the spill from the chroma set.
11.
Use the Type knob to select Misc and the Cntrl
and Values knobs to adjust the parameters.
•
EdgeSo — use this setting to filter the edges
to eliminate undesirable hard edges and add
realism to a scene by simulating depth of field
characteristics.
• BkNorm
— use this setting to offset the
detected level of the chroma background and
allow for fine tuning.
Tip: If the subject image contains fine detail such
as fine hair with a luminance level that is close in
value to the chroma set color background level – it
may be difficult to provide good separation between
background and foreground elements.
DVE Keys
The DVE key allows you to apply digital video
effects, such as scale, crop, aspect ratio, position, and
border to video image or another key type. When the
DVE is applied to another key type, it is said to be
flying (Fly Key).
Tip: You can see where DVE channels are allocated from the
Status
page in DashBoard.
Keep the following in mind when working with a
Fly Key:
• The Fly Key feature consumes a single DVE
channel for self keys, but two DVE channels for an
auto select key.
• The Fly Key feature cannot be applied to a DVE
key.
• The Key Invert feature is not available for a Fly
Key.
To Set Up a DVE Key
The DVE resources for this key may not be available.
Depending on how your switcher is configured, you
may be asked to steal the resources from another
element, or be prevented from using the resources.
1.
Select the keyer that you want to set up a DVE key
on. Click Navigation Menu > Live Assist >
ME and select the ME and key that you want to set
up.
Tip: You can use the same procedure for a MiniME
™
.
2. Select the video signal, on the key bus, that you
want to use for the key. Click Key Fill and select
the video signal you want to use for the key.
3.
Press DVE . Click DVE Key .
4.
Use the X Pos , Y Pos , and Size knobs to
position and size the key. You can also use the
positioner. Use the X-Position , Y-Position , and
Size sliders in the Positioning area to position
and size the key.
5. Press NEXT .
6. Use the Aspect knob to adjust the aspect ratio of
the key. Use the Aspect slider to adjust the aspect
ration of the key.
7. Use the Border knob to apply a border to the key.
Use the Size and Softness sliders in the Border
area to apply a border to the key.
Refer to the section
To Apply a Border to a DVE
Key on page 36 for information on borders.
8. Press NEXT .
9. Crop the key horizontally as follows:
a)
Use the
HCrop
knob to crop the key
horizontally on both the left and right sides at
the same time.
b)
Press
HCrop
and use the
Left/R
knob to crop
the key horizontally on the left side only.
c)
Press
Left/R
and use the
L/Rgt
knob to crop
the key horizontally on the right side only.
10. Use the Left and Right sliders to crop the left and
right sides of the key.
11. Crop the key vertically as follows:
a) Use the VCrop knob to crop the key
vertically on both the top and bottom sides at
the same time.
b) Press VCrop and use the Top/B knob to crop
the key vertically on the top side only.
c) Press Top/B and use the T/Bttm knob to crop
the key vertically on the bottom side only.
12. Use the Top and Bottom sliders to crop the upper
and lower sides of the key.
13. Press NEXT .
14. Use the Mask knob to apply a mask to the key.
Click Mask to apply a mask to the key.
Carbonite Black Operation Manual (v14.0) — Keying • 35