TOPEX Bytton (HSPA+ / LTE)
ByttonLTE(full)_genericUsermanual_sw306FAS_revN.1.docx
Page: 91 / 290
Jul 13 13:10:59 bytton user.notice root: LOG Productie
Jul 13 13:11:00 bytton user.notice root: CONNECT ON WIFI AP: Productie
Jul 13 13:11:01 bytton cron.err crond[1640]: USER root pid 6038 cmd net_moni
…………………………………………………………………………
Also, in
ROUTING>Routes
you can see now the route for the wlan local wireless interface:
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
10.64.64.65 0.0.0.0 255.255.255.255 UH 0 0 0 ppp1
192.168.148.4 0.0.0.0 255.255.255.254 U 0 0 0 wan
172.27.1.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0
191.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 br0
192.168.0.0 0.0.0.0 255.255.0.0 U 0 0 0 wan
0.0.0.0 10.64.64.65 0.0.0.0 UG 0 0 0 ppp1
The wifi connection to “
172.27.1.1
” may be also seen in the System Log:
Jul 19 10:46:23 bytton user.info kernel: cfg80211: Calling CRDA to update
world regulatory domain
Jul 19 10:46:29 bytton user.notice root: LOG guestwifi
Jul 19 10:46:30 bytton user.notice root: CONNECT ON WIFI AP: guestwifi
Jul 19 10:46:30 bytton user.debug kernel: wlan0: authenticate with
00:15:f2:3d:60:36 (try 1)
Jul 19 10:46:30 bytton user.debug kernel: wlan0: authenticated
Jul 19 10:46:30 bytton user.debug kernel: wlan0: associate with
00:15:f2:3d:60:36 (try 1)
Jul 19 10:46:30 bytton user.debug kernel: wlan0: RX AssocResp from
00:15:f2:3d:60:36 (capab=0x401 status=0 aid=3)
Jul 19 10:46:30 bytton user.debug kernel: wlan0: associated
Jul 19 10:46:34 bytton daemon.info dnsmasq[1213]: read /etc/hosts - 1
addresses
Jul 19 10:46:57 bytton daemon.info dnsmasq[1213]: read /etc/hosts - 1
addresses
Jul 19 10:47:01 bytton cron.err crond[1670]: USER root pid 3310 cmd net_moni
Jul 19 10:47:03 bytton daemon.info dnsmasq[1213]: reading /etc/resolv.conf
Jul 19 10:47:03 bytton daemon.info dnsmasq[1213]: using nameserver
172.27.1.1#53
Jul 19 10:47:03 bytton daemon.info dnsmasq[1213]: using nameserver 8.8.8.8#53
------------------------------------------------------------------------------
Radio Channel
: Selects the Wi-Fi channel in the 2400 MHz band.
In this band there are up to 14 channels, placed 5 MHz apart.
When left on “Auto” (default setting) and the AP will automatically
select the radio channel with the strongest signal.
If instead of Auto, you are selecting a certain channel, make sure all
devices are broadcasting on the same channel.
This setting may be left on default, and changed only when
experiencing interference with other devices.
Figure 5-35: Select the Radio Channels of the WiFi Access Point.
