Riso RZ2xx Series Скачать руководство пользователя страница 321

Страница: 321 / 374

RISO Inc. Technical Communications

us.riso.com

CHAPTER 17: TEST MODE

[ 17 - 9 ]

No.

Sensor switch check

Detection status

0400 Master-positioning sensor

Sensor light reflected (Master present) / No reflection ( No master)

0401 Master detection sensor

Sensor light reflected (Master present) / No reflection ( No master)

0402 Master end sensor

Sensor light blocked (Master end seal detected)

0403 Cutter HP SW [Shuttle blade cutter]

SW pressed (Cutter at HP)

0403 Cutter HP SW [Rotary cutter]

SW not pressed (Cutter at HP)

0404 Cutter Stop Position SW [Shuttle blade cutter]

SW pressed (Cutter at end position)

0406 TPH pressure sensor

Sensor light blocked (TPH down position)

0407 Master-making-unit set sensor

Sensor light blocked (Master-making unit cover closed)

0408 Master-making-unit lock sensor

Sensor light blocked (Master-making unit locked in position)

0409 Master-making-unit safety SW

SW pressed (Master-making unit upper cover is closed)

0410 Master-making-unit releasing button

SW ON (Button is pressed )

0420 Master-disposal Jam Sensor

Sensor light is not blocked (Master is detected - jammed)

0421 Master-compression HP Sensor

Sensor light blocked (Master compression plate at HP)

0423 Master-disposal BOX safety SW

SW ON (Master-Disposal Box is set in place)

0425 Master-compression motor FG sensor

Sensor light blocked (Encoder disc is detected)

0426 Master-removal motor FG sensor

Sensor light blocked (Encoder disc is detected)

No.

Motor, solenoid

Remarks

0460 Thermal-pressure motor (CW)

Rotates in clock-wise (CW) direction

0461 Thermal-pressure motor (CCW)

Rotates in counter-clock-wise (CCW) direction

0462 Write pulse motor (CW)

Rotates in clock-wise (CW) direction (master feeding direction)

0463 Write pulse motor (CCW)

Rotates in counter-clock-wise (CCW) direction (master returning direction)

0464 Load pulse motor (CW)

Rotates in clock-wise (CW) direction (master feeding direction)

0466 Write pulse motor + Load pulse motor (CW)

Rotates both the Write & Load pulse motors in
clock-wise (CW) direction (master feed direction)

0467 Master-making-unit release button LED

LED illuminates.

0470 Master removal motor (CW)

Rotates in clock-wise (CW) direction (master feed into master-disposal-box direction)

3. Mater making / Disposal Test Mode (Unit Number 04/05)

No.

Unit check

Details

0480 Cutter motor 1 cycle motion

Performs one cutting motion.

0481 Thermal pressure motor action (TPH down)

Moves the TPH down.

0482 Thermal pressure motor action (TPH up)

Moves the TPH up

0488 Master-making-unit Lock Solenoid ON/OFF action

Press "Start" key to switch ON the Solenoid. Solenoid automatically
switches OFF 10 sec. later.

0489 Storage fan solenoid ON/OFF action

Press "Start" key to switch ON the Solenoid. Solenoid automatically
switches OFF 10 sec. later.

0490 Master compression-plate home positioning

Moves master compression plate to the home position.

0493 Master compression-plate continuous movement

Repeats disposal compression action with interval of 3 seconds between the each.

0494

Cutter motor ON action (cut direction)

[For checking the motor as one part only.

Disconnect the motor from the cutter unit
before activation.]

Rotates the cutter motor in the cut direction (maximum 10 seconds)

No.

Data check

Details

0521 TPH thermistor temperature data

Displays the temperature of the TPH thermistor in "degrees Celsius"

0524 TPH power voltage

Displays the voltage applied to the TPH when the power to the TPH is switched ON.

0527 Master usage start date [only on RZ3 modes]

Displays master use start date stored in Master TAG.
For example, 2004/2/28 will be displayed as 2004 and 0228 in intervals.

Содержание RZ2xx Series























































































































































































































































































































































































Результаты поиска

Содержание RZ2xx Series

Отзывы:

Похожие инструкции для RZ2xx Series

Бренды по названию

Популярные бренды

Riso RZ2xx Series, Техническое руководство

Результаты поиска

Содержание RZ2xx Series

Отзывы:

Похожие инструкции для RZ2xx Series

Бренды по названию

Популярные бренды