Riso RZ2xx Series Скачать руководство пользователя страница 107

Страница: 107 / 374

RISO Inc. Technical Communications

us.riso.com

CHAPTER 6: PRESS SECTION

[ 6 - 9 ]

Adjustment

1. Mounting Position of the Pressure Lever;Spring

Checks and adjustment

(1) Make confidential master on the print drum and turn off the machine power.

(2) Remove the main cover assembly. (Refer to chapter 3)

(3) Hook the pressure spring onto the pressure lever;spring and let the spring hang loose.

(4) Unhook the solenoid lever from the pressure lever;spring and allowing the pressure roller to contact the

print drum by the weight of the pressure spring hooked on the pressure lever;spring.

(5) With the cam follower of the pressure lever;cam touching the pressure cam, confirm that the engraved

line on the pressure lever;spring aligns in between the two engraved lines on the pressure lever;cam.

Pressure lever; spring

Pressure cam

Pressure lever;cam

Pressure spring

Solenoid lever

Pressure lever;cam

Pressure lever;spring

0609

0610

Содержание RZ2xx Series























































































































































































































































































































































































Результаты поиска

Содержание RZ2xx Series

Отзывы:

Похожие инструкции для RZ2xx Series

Бренды по названию

Популярные бренды

Riso RZ2xx Series, Техническое руководство

Результаты поиска

Содержание RZ2xx Series

Отзывы:

Похожие инструкции для RZ2xx Series

Бренды по названию

Популярные бренды