Riso RZ2xx Series Скачать руководство пользователя | Manualshive

Страница: 134 / 374

background image

RISO Inc. Technical Communications

us.riso.com

CHAPTER 8: PRINT DRUM SECTION

[ 8 - 4 ]

3. Print Drum Rotation Mechanism

When the main motor rotates, the drive is transferred in following sequence.

The main motor drive is transferred to the main shaft assembly via main belt, and via the drive joint the drum
joint receives the drive and rotates the flange-R of the print drum.

The flange gear on flange-R drives the squeegee idle gear and the drive is transferred to the squeegee drive
gear to rotate the squeegee roller.

As the squeegee roller rotates, the squeegee roller attached on the squeegee roller shaft rotates and transfers
the drive to the driven shaft gear and rotates the driven shaft.

The squeegee drive gear contains a one-way clutch to prevent the squeegee roller from rotating in the
reverse direction if by accidentally the print drum is rotated in the opposite direction by hand.

The doctor roller is fixed in position and does not rotate.

Squeegee roller

0803

Squeegee idle gear

0804

Squeegee gear

Flange-R

Drum joint

Drive joint

Flange-R

Flange gear

Squeegee drive gear

Driven shaft gear

Driven shaft

Doctor roller

«
...
132
133
134
135
136
...
»

Содержание RZ2xx Series























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZ2xx Series

Бренд: ACT Страницы: 24

Бренд: Teac Страницы: 38

Бренд: Copystar Страницы: 21

Бренд: Copystar Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды