manualshive.com logo in svg

Riso RZ2xx Series, Техническое руководство, Страница: 164 / 374

Поделиться
Скачать
Riso RZ2xx Series Скачать руководство пользователя страница 164

RISO Inc. Technical Communications

   us.riso.com

CHAPTER 9:  CLAMP UNIT

[ 9 - 4 ]

3. Drum Position-A Compensation

The print drum rotates to remove the master and as it comes back to position-A, the clamp opening cam at
its lowered position opens the clamp plage and lifts up the ejection plate.

As the print drum stops at position-A, the clamp motor turns ON to rotate the clamp cam until the light path of
the clamp sensor-B becomes unblocked by the disc.  This action brings the position-A compensation plate
down to catch the plastic compensator pin on the print drum to hold the print drum at position-A.

0906

0907

Clamp cam

Position-A compensation plate

Clamp opening cam

Clamp plate

Clamp sensor-B

Master ejection plate

Compensator pin

Содержание RZ2xx Series























































































































































































































































































































































































Отзывы:

Нет отзывов