Riso RZ2xx Series Скачать руководство пользователя страница 235 | Manualshive

Страница: 235 / 374

background image

RISO Inc. Technical Communications

us.riso.com

CHAPTER 14: MASTER MAKING SECTION

[ 14 - 3 ]

2. Set Detection Mechanism

Master making unit set detection mechanism

As flatbed section cannot be opened or closed, the unit has a mechanism in which the master making unit
can be pulled out.

The pulling out and insertion of the master making unit are conducted at print drum position-B stop position.
The master making U safety switch and the master making U lock sensor confirm that the master making
unit is set.

When the master making U safety switch turns OFF, the main motor, clamp motor, master removal compression
motor and master removal transport motor are electrically designed not to activate.

The master making unit upper cover detection mechanism

The master making unit upper cover set sensor confirms that the master making unit upper cover is set, and
the master setting operation is performed once the cover is set.

Master end detection

The end of the master roller is confirmed by the master end sensor detecting the black end mark attached on
the tail end of the master material on the master roll. The master end sensor checks every 10 ms while the
master is being transported, and the master roll LED on the operation panel illuminates when the end mark
is detected twice in succession.

Master making unit

Master making U safety SW

Master making U lock sensor

1402

1403

«
...
233
234
235
236
237
...
»

Содержание RZ2xx Series























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZ2xx Series

Бренд: Tascam Страницы: 8

Carry HDD PRO118

Бренд: U-Reach Страницы: 20

Бренд: StarTech.com Страницы: 2

Бренд: Summation Technology Страницы: 36

AMIGO II EVEREST

Бренд: Rimage Страницы: 4

Бренд: Rimage Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды