Riso RZ2xx Series Скачать руководство пользователя страница 299

Страница: 299 / 374

RISO Inc. Technical Communications

us.riso.com

CHAPTER 16: PANEL MESSAGE

[ 16 - 21 ]

Option errors

Error Type

B01 [Keycard counter: No card]

Description

B01-xxx
Insert Card in Key/Card Counter

To reset

display

Insert card.

Error Point

Error Conditions

730

Keycard counter: No card

Error Type

B22 [Job separator: Power off]

Description

B22-xxx
!! Job Separator is OFF !!
Turn On Power Switch of it

To reset

display

Press Reset Key and check and switch ON the power of Job Separator.

Error Point

Error Conditions

721

With the “Tape separation” function set ON, no power is supplied to the job separator when
start key is pressed.

727

After cluster-A signal turned ON, BUSY-signal stayed "L" more than 7 seconds (power to job
separator was turned OFF while the tape is being ejected.

Error Type

B23 [Job separator: No tape]

Description

B23-xxx
No Paper Tape in Job Separator
Replace Tape Roll

To reset

display

Press Reset Key and set paper tape in Job Separator.

Error Point

Error Conditions

722

With the “Tape separation” function set ON, no tape detected in the job separator when the
start key is pressed.

723

No tape remains in job separator upon completion of the tape-ejection operation.

Error Type

B24 [Job separator: Tape jam]

Description

B24-xxx
Paper Tape Jam in Job Separator
Remove Paper Tape

To reset

display

Press Reset Key and remove the jammed tape.

Error Point

Error Conditions

724

Tape jam detected when the start key is pressed with the “Tape separation” function set to
ON.

725

The tape-jam detection signal is "H" for more than 1.2 seconds after cluster-A signal turns ON
(tape misfeed).

726

Job separator tape-jam detection signal is “L” when the BUSY signal changes from “L” to “H”
(or after 7 sec. at “L”) after the cluster-A signal goes ON (tape misfeed).

Содержание RZ2xx Series























































































































































































































































































































































































Результаты поиска

Содержание RZ2xx Series

Отзывы:

Похожие инструкции для RZ2xx Series

Бренды по названию

Популярные бренды

Riso RZ2xx Series, Техническое руководство

Результаты поиска

Содержание RZ2xx Series

Отзывы:

Похожие инструкции для RZ2xx Series

Бренды по названию

Популярные бренды