Riso RZ2xx Series Скачать руководство пользователя страница 152

Страница: 152 / 374

RISO Inc. Technical Communications

us.riso.com

CHAPTER 8: PRINT DRUM SECTION

[ 8 - 22 ]

13. Removing the Flange-F

(1) Make a confidential master on the print drum and pull out the drum from the machine.

(2) Remove the following components.

- Screen assembly
- Master clamp base assembly
- Drum body
- Drum side frames (2pcs)

(3) Disconnect two connectors from the print drum PCB, detach one reusable band from the drum front

frame assembly and detach the drum front frame assembly by removing screws (M4x8: 5pcs).

(4) Remove the lock-clip on the flange support roller found at the bottom of the drum, and detach the roller.

(5) Detach the flange-F.

* Remaining two flange support rollers can be removed after removing the flange-F.

Reusable band

Lock-clip

Flange support roller

Flange F

Drum front frame assembly

0854

0855

0856

Содержание RZ2xx Series























































































































































































































































































































































































Результаты поиска

Содержание RZ2xx Series

Отзывы:

Riso RZ2xx Series, Техническое руководство, Страница: 152 / 374

Результаты поиска

Содержание RZ2xx Series

Отзывы: