Riso RZ2xx Series Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 374

background image

RISO Inc. Technical Communications

us.riso.com

CHAPTER 7: PAPER EJECTION SECTION

[ 7 - 3 ]

2. Paper Separator Mechanism

The tip of the separator is positioned close to the print drum surface when separating the paper from the print
drum. As the print drum rotates and the clamp plate base approaches the separator, the cam follower on the
separator lever assembly rides on the high part of the main gear. The high part of the main gear pushes the
separator lever assembly down. This action rotates the separator shaft and brings the tip of the separator
down, away from the print drum to clear the clamp plate base on the print drum.

During the removal and insertion of the print drum into the machine, the tip of the separator needs to move
away from the print drum to prevent being hit by the print drum. A plastic release arm attached on the slide
rail pushes the release lever and rotates the separator shaft to move the tip of the separator down, away from
the print drum during the print drum removal and insertion.

Main gear

Separator

Slid rail

Separator lever assembly

Separator DOWN

Separator

Separator shaft

Release lever

Release arm

Print drum

Separator UP

0702

0703

0704

«
...
109
110
111
112
113
...
»

Содержание RZ2xx Series























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZ2xx Series

Бренд: Rimage Страницы: 5

Бренд: Datatronics Страницы: 13

Бренд: Zipsnip Страницы: 14

DIRECTOR series

Бренд: MF DIGITAL Страницы: 8

Бренд: MF DIGITAL Страницы: 73

Бренд: General International Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды