Riso RZ2xx Series Скачать руководство пользователя | Manualshive

Страница: 100 / 374

background image

RISO Inc. Technical Communications

us.riso.com

CHAPTER 6: PRESS SECTION

[ 6 - 2 ]

Clamp plate base

Pressure cam

Print drum

Pressure lever;spring

Pressure spring

Pressure lever;cam

Pressure shaft

Main motor

Solenoid lever

Pressure solenoid

0601

Mechanism

1. Press Mechanism

At the start of a printing job, the pressure solenoid turns ON when the print drum rotates to a given angle, and
tries to unhook the solenoid lever away from the pressure lever;cam which is still engaged until the print drum
makes further rotation.

As the print drum continues to rotate, the cam follower on the pressure shaft;cam start to ride on the high
portion of the pressure cam, making the pressure lever;cam to swing in the clockwise direction with its pivot
on the pressure shaft. As the lever starts to ride on the highest point on the cam, it touches and starts to
swing the pressure lever;spring in the clockwise direction. As the pressure lever;spring swings in the clockwise
direction with the pivot at the pressure shaft, the solenoid lever disengages and allows the pressure solenoid
to pull the solenoid lever further in, completely disengaging it from the pressure lever:spring.

As the print drum rotates further, the pressure lever;cam starts to ride on the lower portion of the pressure
cam, causing the lever to swing back in the counterclockwise direction. The pressure lever;spring, freed
from the pressure lever;cam, is pulled by the pressure spring to rotates in the counterclockwise direction,
rotating the pressure shaft in the counterclockwise direction together. The counterclockwise direction rotation
of the pressure shaft lifts the pressure roller up and press against the print drum.

When the clamp base plate of the print drum approaches the pressure roller, the pressure cam pushes the
pressure lever;cam in the clockwise direction and lowers the pressure roller so the roller does not hit the
clamp plate.

The pressure solenoid is kept ON all through the printing job. The solenoid goes OFF when the print drum
comes to a given angle at the end of the printing job.

«
...
98
99
100
101
102
...
»

Содержание RZ2xx Series























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZ2xx Series

Бренд: Octave Страницы: 80

Бренд: Datatronics Страницы: 13

8STSATDOCK2REU3

Бренд: StarTech.com Страницы: 2

Бренд: Teac Страницы: 38

USBDUPLICATOR/11

Бренд: Teac Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды