manualshive.com logo in svg

Riso RZ2xx Series, Техническое руководство

Riso RZ2xx Series - это высококачественное оборудование для печати. Техническое руководство доступно бесплатно для скачивания из {сайт}. Пользователи могут получить подробную информацию о настройке и использовании устройства, обеспечивая эффективную работу и отличный результат печати.

Поделиться
Скачать
background image

RISO Inc. Technical Communications

   us.riso.com

CHAPTER 17:  TEST MODE

[ 17 - 3 ]

No.

Data clear

Details

Forcibly clears the jam.

This test mode can also be used to clear error data for items for which
jam can otherwise be cleared only by the jam release procedure.
Consumables errors cannot be cleared.

User area memory clear

(Memo down all the settings before activation.)

Initializes data in user area memory to the programming defaults.

Normal area test mode memory clear for test modes
on the machine.

(Memo down all the settings before activation.)

Initializes all normal area test mode settings on the machine
to their programming default values.
The protected area test modes stay unchanged.

Maintenance Call master count clear

Clears the maintenance-call message for master making.

Maintenance Call copy count clear

Clears the maintenance-call message for printing.

Maintenance Call print drum print count clear

Clears the maintenance-call message for print drum.

Normal area test mode memory clear for test modes
on the print drum.

(Memo down all the settings before activation.)

Initializes all normal area test mode settings within the EEPROM of the print drum to
their programming default values.   The protected area test modes stay unchanged.

0117

Clearing User Memory

Clearing Normal Area Test-Mode Data Memory [MACHINE]

Clearing Normal Area Test-Mode Data Memory [PRINT DRUM]

0110

Clearing Jam Status Data

0115

Maintenance Count Clear (print drum)

0111

0112

0113

0114

Maintenance Count Clear (master making)

Maintenance Count Clear (printing)

No.

Sensors, switches

Detection status

0001 Wakeup Key

Key Pressed

0002 Solenoid counter connection signal

Solenoids counter connected

0003 24V A output signal

24V-A ON (24V output)

0004 24V B output signal

24V-B ON (24V output)

0005 Serviceman safety SW (Rear cover safety SW)

Short interval beep sound = SW ON (Rear Cover installed).
Long interval beep sound = SW OFF (Rear Cover removed: Interlock Safety Switch off).

No.

Motor solenoid system

Remarks

0062 Wakeup LED

LED Illuminates

No.

Unit check

Details

0101

Machine Clock activation
  (Available only on RZ3 series)

Activates time set by Test Modes No.0171 to 0173.
The new clock time set by test mode No. 0171 through No.0173 will not be
activated unless this test mode No. 0101 is activated.

Test Print E (Dot1 + Cross Lines)   [Available only on RZ3 series]

Error Record

Stores the error logs accumulated on FLASH memory into CF card.

Test Print A (checkered)

Test Print F (Dot2 + cross stripes)   [Available only on RZ3 series]

Creates Test pattern 6 (Dot 1 + Cross Lines)

Creates Test pattern 7 (Dot 2 + Cross Lines)

Test Print B (cross stripes)

Creates Test pattern 1 (Checker Flag)

Speed 1 = 60rpm           Speed 2 = 80rpm          Speed 3 = 100rpm          Speed 4 = 110rpm          Speed 5 = 130rpm

Creates Test pattern 2 (Cross Lines)

Test Print C (Dot1)   [Available only on RZ3 series]

Creates Test pattern 4 (Dot 1 )

Creates Test pattern 5 (Dot 2 )

Test Print D (Dot2)   [Available only on RZ3 series]

0087

0088

Paper-Feed Test (continuous feeding)

Low-Speed Printing Operation

Unit Initialization

0089

0094

0095

1. System Panel Test Mode

0080

Press “Start” key to switch on the suction fan.  Prints at 15 rpm only while “Test print” key is pressed.
Printing stops when "Test Print" key is released, and resumes if the key is pressed again.   Press “Stop” to switch suction fan off.

Prints continuously at 15 rpm.

Stepped Printing Operation

0081

0082

0083

0084

0085

0099

0100

Rev Manual Event Code Set

Initializes the mechanical moving units to their home positions (TPH pressure, master compression plate, drum lock,
clamp unit, vertical print position, printing pressure).

System Configuration Data Output

Creates a master for the CI system data.

Stores the settings set in Test mode "No. 196 to 198" manual event codes into REv Flash address in CF card.

Содержание RZ2xx Series























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZ2xx Series

Yurex MantraJet 1050 Operator'S Manual preview
MantraJet 1050
Бренд: Yurex Страницы: 21

Бренды по названию

Популярные бренды

Загрузить еще бренды