Riso RZ2xx Series Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 374

background image

RISO Inc. Technical Communications

us.riso.com

CHAPTER 3: MAIN DRIVE

[ 3 - 13 ]

0321

Master loading cover

Adjustment

1. Print-Drum “Position-A” Adjustment

Checks and adjustment

(1) Open the front door.

(2) Remove a screw ( M4x8: 1pc) to detach the master loading cover.

(3) Go into the test mode, and run Test Mode No.881 (Position-A stop) to rotate and stop the print drum at

“Position-A”.

(4) Run Test Mode No.884 (Clamp 3-step movement) to confirm that when the position-A compensator arm

comes down on the print drum on the 2nd of the 3 steps of the test mode, the print drum rotates back a
distance of 3mm maximum or stays still. The print drum should not rotate forward when the compensator
arm comes down.

(5) If Position-A of the print drum is not within the specified position, run Test Mode No.941 (Print drum

position-A adjustment ) to adjust the “Position-A” of the print drum.

(6) Repeat from step (3) until the position is correctly adjusted.

This adjustment does not affect the print drum position-B stop position.

2. Print-Drum “Position-B” Stop Position Adjustment

Checks and adjustment

(1) Open the front door and press the green colored print drum release button.

(2) Confirm that the print drum slides out of the machine smoothly when pulled out by hand.

(3) If the print drum does not come out smoothly, run Test Mode No. 942 (Print drum Position-B Adjustment)

to adjust the position-B stop position of the print drum.

(4) Repeat from step (1) until the position is correctly adjusted.

This adjustment does not affect the print drum position-A.

NOTE: The print drum position-B stop position is calculated from the position-B of the machine by

the pulse count of the main motor FG sensor (refer to page 3-3).

«
...
49
50
51
52
53
...
»

Содержание RZ2xx Series























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZ2xx Series

Бренд: Greystone Страницы: 36

Бренд: U-Reach Страницы: 40

Бренд: Kanguru Страницы: 27

Бренд: Teac Страницы: 1

Бренд: Teac Страницы: 34

Бренд: Teac Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды