Riso RZ2xx Series Скачать руководство пользователя страница 303

Страница: 303 / 374

RISO Inc. Technical Communications

us.riso.com

CHAPTER 16: PANEL MESSAGE

[ 16 - 25 ]

Error Type

D04 [Incorrect ink cartridge]

Description

D04-xxx
Wrong-type Ink Cartridge Installed or Cannot Read Ink Info
Replace Ink Cartridge or Contact dealer/Riso office

To reset

display

Replace with correct ink cartridge.

Error Point

Error Conditions

534

Incorrect ink cartridge is used.

560

Ink RF-Tag is not detected on ink bottle.

561

Ink RF-Tag communication error (communication with the ink cartridge was interfered by
noise).

562

Wrong ink cartridge information on the Ink RF-Tag.

564

Detected a mismatch in the Ink RF-Tag.

575

RF-Tag software error.

Error Type

D05 [Master not set]

Description

D05-xxx
Set Master in Place

To reset

display

Insert leading edge of the master material into the master entrance and close the master
making unit.

Error Point

Error Conditions

210

Master detection sensor is OFF (not detecting master material).

Error Type

D07 [Master disposal box not set]

Description

D07-xxx
Set Master Disposal Box in Place

To reset

display

Set master disposal box in the machine.

Error Point

Error Conditions

310

Master disposal box safety switch is OFF.
(Does not detect the error during low-power mode in which 24V power is down)

Содержание RZ2xx Series























































































































































































































































































































































































Результаты поиска

Содержание RZ2xx Series

Отзывы:

Похожие инструкции для RZ2xx Series

Бренды по названию

Популярные бренды

Riso RZ2xx Series, Техническое руководство

Результаты поиска

Содержание RZ2xx Series

Отзывы:

Похожие инструкции для RZ2xx Series

Бренды по названию

Популярные бренды