manualshive.com logo in svg

Riso RZ2xx Series, Техническое руководство

Riso RZ2xx Series - это высококачественное оборудование для печати. Техническое руководство доступно бесплатно для скачивания из {сайт}. Пользователи могут получить подробную информацию о настройке и использовании устройства, обеспечивая эффективную работу и отличный результат печати.

Поделиться
Скачать
background image

RISO Inc. Technical Communications

   us.riso.com

CHAPTER 17:  TEST MODE

[ 17 - 10 ]

No.

Data setting

Details

Description

Adjusts return movement a little bit after the master-positioning sensor goes ON
to perform inching operation during master setting or following master cutting action.

Setting 

Range :                      0mm to +10.0mm (+ is master moving back direction)
                                   0 to +100 (example:  +15 = 1.5mm moving back)
Unit :                          1 (0.1mm)
Default :                     50 (5.0mm)

Description

Adjusts the master-making start position <independent from
Clamp-range adjustment>(adjusts master stop position distance
from master-positioning sensor before read/write-signal goes ON).

Setting 

Range :                      ±5.0mm from the programmed default position
                                           (+ moves printed image up)
                                   0 to ±50 (example: 15 = 1.5 mm)
Unit :                          1 (0.1mm)
Default :                     0 (0mm)

Description

Adjusts the master-making length.

Setting 

Range :                     ±10.0mm from the programmed default position
                                          (+ increases length).
                                  0 to ±100 (example:   15 = 1.5mm)
Unit :                         1 (0.1mm)
Default :                    0 (0mm)

Description

Adjusts the master-clamp range during loading of the master. (independent from master-making.
length adjustment.)

Setting 

Range :                     ±10.0mm from the programmed default position
                                         (+ increases clamping amount).
                                  0 to ±100 (example: 15 = 1.5mm)
Unit :                         1 (0.1mm)
Default :                    0 (0mm)

0542

Master-making length adjustment

0543

Master-clamp-range adjustment

0540

Write start-position adjustment

0541

Master Front-End Position Adjust

Description

Adjusts the length of one master (changes cut timing).

Setting 

Range :                     ±10.0° from 0°  (+ increases the master length).
                                  0 to ±100 (example: 100 = 10°)
Unit :                         5 (0.5°)
Default :                    0 (0°)

Description

Adjusts the writing speed.  (Adjusts the speed of the write pulse motor.)

Setting 

Range :                     ±10.0% from the programmed speed
                                       ( - shrinks the image in master making.).
                                  0 to ±100 (example: 15 for -1.5%)
Setting unit :             1 (0.1%)
Default :                    0  (0%)

Description

Sets the pulse count for the compression-limit position (maximum end position).

Setting 

Range :                     106 to 163 pulses
                                                    (Master compression plate position 65°  to 100° from HP).
Unit :                         1 (1 pulse)
Default :                    130 pulses (compression plate angle 90° from HP)

Description

Sets the stop time duration for one master compression.  (The compression finishes when one it
takes one certain time for the encoder disc on master compression motor to make one rotation).

Setting 

Range :                      5ms to 70ms
                                   5 to 70  (example: 15 = 15ms)
Unit :                          1 (1ms)
Default :                     53 (53ms)

Mater compression duration adjustment

0575

Master compression-limit position (maximum end position).

0573

0544

Master-making speed adjustment

0547

Master cut length adjustment

Содержание RZ2xx Series























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZ2xx Series

Virtual Console FCD-CFxx User Manual preview
FCD-CFxx
Бренд: Virtual Console Страницы: 18
Ricoh Priport DX 4640PD Operating Instructions Manual preview
Priport DX 4640PD
Бренд: Ricoh Страницы: 240
Ricoh Pentax 30100 Quick Start Manual preview
Pentax 30100
Бренд: Ricoh Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды