Riso RZ2xx Series Скачать руководство пользователя страница 249

Страница: 249 / 374

RISO Inc. Technical Communications

us.riso.com

CHAPTER 14: MASTER MAKING SECTION

[ 14 - 17 ]

6. Removing the Master Detection Sensor and Master End Sensor (send) Assembly

(1) Pull out the master making unit and switch off the machine power.

(2) Open the master making unit upper cover and remove the master roll.

(3) Detach the master making cover front by removing screws (M4x8: 4pcs).

(4) Detach the master making PCB by removing screws (M3x6: 2pcs)

(5) Detach the master making PCB bracket (M4x8: 1 pc)

(6) Remove the stopper plates front and rear by removing screw (M3x6: 1pc each).

* Since the set guide plate-B is forced up by two springs, set guide plate-B springs front and rear, press

down the set guide plate-B when removing the stopper plates.

(7) Detach and hang loose the master-flange assembly (rear) by removing screws (M3x6: 2 pcs).

(8) Detach the set guide plate-B, together with the set guide plate shaft by removing the mounting screws of

the shaft (M3x6: 1 pc each).

- Continues on next page -

Master making PCB

Master making PCB bracket

1485

1484

Master detection sensor and Master end sensor (send)

Set guide plate-B

1433

Set guide plate shaft

Содержание RZ2xx Series























































































































































































































































































































































































Результаты поиска

Содержание RZ2xx Series

Отзывы:

Riso RZ2xx Series, Техническое руководство, Страница: 249 / 374

Результаты поиска

Содержание RZ2xx Series

Отзывы: