manualshive.com logo in svg

Riso RZ2xx Series, Техническое руководство, Страница: 203 / 374

Поделиться
Скачать
Riso RZ2xx Series Скачать руководство пользователя страница 203

RISO Inc. Technical Communications

   us.riso.com

CHAPTER 11:  FB ORIGINAL SCANNING SECTION (600 dpi)

[ 11 - 13 ]

7. Removing the FB Read Pulse Motor

(1) Switch off the machine power and remove the scanner cover;paper feed.

(2) Remove the mounting screws (M3x6: 4pcs) of the FB read pulse motor mounting bracket, unhook the

timing belt located inside the scanner unit and detach the motor with the mounting bracket attached.

(3) Detach the FB read pulse motor from the bracket by removing screws (M3x6: 2pcs).

< Precaution in Assembly >

Pull the bent edge of the motor bracket in the direction indicated by an arrow on the photograph below to
apply adequate tension to the timing belt when tightening the mounting screws of the FB read pulse motor
bracket onto the scanner unit.

Motor bracket

FB read pulse motor

Bent edge

FB read pulse motor

Timing belt

1121

1122

Содержание RZ2xx Series























































































































































































































































































































































































Отзывы:

Нет отзывов