Riso RZ2xx Series Скачать руководство пользователя страница 284

Страница: 284 / 374

RISO Inc. Technical Communications

us.riso.com

CHAPTER 16: PANEL MESSAGE

[ 16 - 6 ]

Error Type

P03 [Clamp motor lock]

Description

P03-xxx
!!System Error!!
Press Reset Key
If Recovery has Failed, Call Service

To reset

display

Press Reset Key

Error Point

Error Conditions

500

Clamp sensor A is OFF after the completion of the clamp unit initialization or home positioning
movement.

501

Clamp sensor B does not change within 1 second from the time the clamp motor operates in
the forward direction.

502

Clamp sensor B does not change within 1 second from the time the clamp motor operates in
the reverse direction.

503

Clamp sensor A does not go ON within 3 seconds when the clamp unit makes initialization
movement.

504

At the start of Clamp plate open/close action, the detection sequence of clamp-sensors A &
B are abnormal.

505

At the start of print drum Position-A compensation movement, the detection sequence of
clamp-sensors A & B are abnormal.

506

At the start of Clamp unit Home-positioning movement, the detection sequence of clamp-
sensors A & B are abnormal.

507

Clamp sensor A is ON after the clamp release action is completed.

508

Clamp sensor A is ON after the A-position compensating movement is completed.

545

Clamp unit is not in the home position while the print drum is in movement (cause due to the
clamp motor).

Error Type

P04 [Ink overflow]

Description

P04-xxx
!!System Error!!
Press Reset Key
If Recovery has Failed, Call Service

To reset

display

Press Reset Key after correcting the ink overflow condition. (No ink on the ink overflow
sensor.)

Error Point

Error Conditions

513

The overflow sensor is ON for a set number of times in succession during the 10-millisecond-
interval overflow-sensor check.

Содержание RZ2xx Series























































































































































































































































































































































































Результаты поиска

Содержание RZ2xx Series

Отзывы:

Riso RZ2xx Series, Техническое руководство, Страница: 284 / 374

Результаты поиска

Содержание RZ2xx Series

Отзывы: