Riso RZ2xx Series Скачать руководство пользователя страница 269 | Manualshive

Страница: 269 / 374

background image

RISO Inc. Technical Communications

us.riso.com

CHAPTER 14: MASTER MAKING SECTION

[ 14 - 37 ]

Adjustment

1. Thermal Power of Thermal Print Head

The thermal power must always be adjusted each time a TPH (thermal print head) is replaced.

(1) Activate test mode No.9874 to access into the protected area test mode.

(2) Run test mode No.1234 (TPH resistance input) and enter the resistance value imprinted on a sticker

attached on each TPH. Press START key to enter the value.

(3) Press <RESET> key to return to return back to the normal operation mode.

2. Master Clamp Range Adjustment

Checks and adjustment

(1) Make a master and mark a short straight line at the center of the master along the edge of the clamp

plate so the measurement of the mater under the clamp plate can be measured.

(2) Open the clamp plate and measure from the leading edge of the master to the marking made. The

measured length should be 18mm (plus or minus 1mm).

(3) If the measurement is out of the specified range, make an adjustment using test mode No. 543 (master

clamp range adjustment) clamp range adjustment.

* Increasing the setting by the test mode increases the master clamp amount.

3. Write Start Position Adjustment

Checks and adjustment

(1) Run Test mode No.80 (Test print A) to make a master.

(2) Remove the leading edge of the master by opening the clamp plate of the print drum and measure the

distance from the leading edge of the master to the write start position (top of the image) to confirm that
the distance is 63mm (plus or minus 1mm) measured at about the center of the master material.

(3) If the measurement is out of the specified range, run test mode No.541 (Write start position adjustment)

and make an adjustment.

* Increasing the settings by the test mode decreases the distance, moving the image up on the master

material.

* Master Clamp Range Adjustment must be made before the Write Start Position Adjustment.

«
...
267
268
269
270
271
...
»

Содержание RZ2xx Series























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RZ2xx Series

Бренд: Lanier Страницы: 128

Producer III 8100

Бренд: Rimage Страницы: 1

Professional Endeavor

Бренд: Rimage Страницы: 5

Бренд: RANSOM & RANDOLPH Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды