Ricoh Ri 100 Скачать руководство пользователя страница 230

Страница: 230 / 260

Message

Causes

Solutions

Right Front Cover is
open / Close Right Front
Cover

The right front cover is
open.

Close the right front cover.
See page 230 "Cover Open".

Right Int. Unit almost full

Internal unit is a service
replacement part.

For details about internal unit replacement,
contact your sales or service representative.

Routine Maint. Required

Regular maintenance is
needed.

Clean both the Maintenance Unit and the
print head.
See page 133 "Clean Maint Unit" and
page 136 "Auto Head Maint.".

SCXXX-XX Power Off
On / Call Service if error
reoccurs

An error has occurred.

Turn the machine off and then on. If the
message reappears, contact your sales or
service representative.

Set Tray

The cassette is not
loaded.

Load the cassette on the cassette stand.

Size Mismatch
Tray to print or Stop to
reset

The cassette of the
specified size is not set.

Change the print size. For details, see
page 87 "Selecting the Cassette Size and
Direction". To continue printing without size
mismatch, press the [Tray] key.

Temp. alert Please wait...

The machine is too hot or
cold at start-up.

Wait until "Ready" appears on the display.

Top Cover open close it
to / restart machine /
Power Off On

The top cover is open.

Close the top cover.
See page 230 "Cover Open".

Used Ink Collect Unit is
set / Replace Ink
Collector Unit

A used ink collector unit
was installed.

Install a new ink collector unit.
See page 188 "Replacing an Ink Collector
Unit".

Used Ink Crtrdge /
Replace Ink Crtg

A used ink cartridge was
installed.

Replace the ink cartridge for the color
indicated by the or icon.
See page 182 "Replacing an Ink Cartridge".

• If this does not eliminate the problem, contact your sales or service representative.

9. Troubleshooting

228

Содержание Ri 100





































































































































































































































































Результаты поиска

Содержание Ri 100

Отзывы:

Похожие инструкции для Ri 100

Бренды по названию

Популярные бренды

Ricoh Ri 100, Руководство по эксплуатации

Результаты поиска

Содержание Ri 100

Отзывы:

Похожие инструкции для Ri 100

Бренды по названию

Популярные бренды