Rhymebus RM5G Скачать руководство пользователя страница 80

Страница: 80 / 104

7. OPERATIONAL PROCEDURES, MAINTENANCE,

AND TROUBLE SHOOTING

- 72 -

(1) Operational procedure and operations

DANGER

1. After turn off power source, please don't touch the inverter and

change the wiring when indicator is light.

CAUTION

1. After wiring, double check is absolutely necessary.

2. Keep terminal connected tightly with wire.

A. Be sure that the voltages of power source, motor and inverter are

matched.

B. Connect power source lines to R, S and T terminals of inverter.

C. Turn on the power source, set the function codes and parameters,

and check that the voltages of U, V and W terminals are correct or

not. Then, turn off the power source.

D. Turn off the power source and wait until that the LED is off, motor

lines are connected to U, V and W terminals of inverter.

E. Turn on the power source and check the rotating direction of motor

with low speed.

User has to use the ON/OFF switch on keypad to start/stop inverter.

If the switch of power source is used to start/stop inverter, the

lifetime of inverter will be reduced.

G. It is not permitted that use of a magnetic contact installed between

an inverter and the motor to start/stop motor. In general, the start

current of motor is about 5 to 8 times of its rated current.

H. How to properly size an inverter for a single-phase power supply

with a three-phase motor.

Determine motor horsepower required for particular application.

Divide the motors full load amperage by 0.5 the result of that

calculation is the basis of sizing the inverter. Select an inverter with

continuous amperage rating that is equal to or greater than the result.

Formula: FLA of motor / 0.5 = Inverter Amps

EXAMPLE:

a. Invert selection: 230Vac, 3HP motor = 9.6A 9.6A/0.5 = 19.2A

230Vac, 3HP inverter = 11A continuous

230Vac, 7.5HP inverter = 25A continuous

You would select the 7.5HP inverter for this application.

b. Parameters setting: Without doing this setup could result in drive

and/or motor failure

F_048 motor rated current = 9.6A (according to the spec. of motor)

F_068 Level of overload setting = 80 (The half of original

setting160%)

F_071Level of stall prevention at the constant speed =80 (The half

of original setting160%)

Содержание RM5G









































































































Результаты поиска

Содержание RM5G

Отзывы:

Похожие инструкции для RM5G

Бренды по названию

Популярные бренды

Rhymebus RM5G, Руководство пользователя

Результаты поиска

Содержание RM5G

Отзывы:

Похожие инструкции для RM5G

Бренды по названию

Популярные бренды