Rhymebus RM5G Скачать руководство пользователя страница 44

Страница: 44 / 104

~DESCRIPTIONS OF FUNCTION CODE SETTINGS~

- 36 -

F_ 134

: Selections of resumption of factory setting

This function is used to resume the factory settings and store/write

settings between inverter and KP-201C. This is the last item of the

function.

Note:

The codes

and

are copy function to be

used for the case of several inverters with the same

settings.(Ref.Page22)

: Useless
: Clear fault records
: Resume the factory settings of 60 Hz.
: Resume the factory settings of 50 Hz.
: Store settings
: Resume last settings
: Digital keypad (KP-201C)

←

inverter parameters

: Digital keypad (KP-201C)

→

inverter parameters

F_007

: Speed constant

The range of setting is 0.00~500.00 to set the value of MPM

displayed on keypad Line velocity = speed constant(F_007)

output frequency, which is the value of MPM, displayed in the

monitor mode.

F_008

: No. decimal of speed display

Increasing the no. decimal to display the monitored signal more

precisely. The range of F_008 is 0~3.

Note : that any display can be set to be the main display, and that if

the keypad has not been operated and the auxiliary display

has been displayed for about 3 minutes, the main display is

shown.

Содержание RM5G









































































































Результаты поиска

Содержание RM5G

Отзывы:

Похожие инструкции для RM5G

Бренды по названию

Популярные бренды

Rhymebus RM5G, Руководство пользователя

Результаты поиска

Содержание RM5G

Отзывы:

Похожие инструкции для RM5G

Бренды по названию

Популярные бренды