Rhymebus RM5G Скачать руководство пользователя страница 25

Страница: 25 / 104

CHAPTER 3 TYPES OF KEYPADS

- 17 -

(1) Digital keypad (KP-201C)

1.T.S : Indicator of the status of

terminals .

2.Indicator of unit.

1. Constant speed : LED is light.

2. Acc./dec. : LED flashes.

Inverter begins to output

frequency.

Increase or decrease
setting.

1.Inverter stops frequency

output.

2.Reset.

1.Enter parameter setting mode.

2.Back to function code setting

mode.

3.Switch the monitor mode.

1.Enter function code

setting mode.

2.Back to monitor mode.

1.If LED is light, speed is

command by keypad.

2.If LED is not light,speed is

command by terminals.

(2) Analog keypad (KP-202C)

Note: Keypad KP-201B andKP-202B still can be used in the

RM5G/5P inverter.

Setting potentiometer

1.If LED is light, speed is

command by keypad.

2.If LED is not light,speed is

command by terminals.

1.Inverter stops frequency

output.

2.Reset.

Inverter begins to output

frequency.

1. Constant speed : LED is

light.

2. Acc./dec. : LED flashes.

The LED will be light, if the

corresponding ADJ has been

chosen by RSW.

Содержание RM5G









































































































Результаты поиска

Содержание RM5G

Отзывы:

Похожие инструкции для RM5G

Бренды по названию

Популярные бренды

Rhymebus RM5G, Руководство пользователя

Результаты поиска

Содержание RM5G

Отзывы:

Похожие инструкции для RM5G

Бренды по названию

Популярные бренды