Rhymebus RM5G Скачать руководство пользователя страница 30

Страница: 30 / 104

OPERATIONS OF KEYPADS ~

- 22 -

G. Copy and resume factory settings

a. The function of copy is defined to store settings in digital keypad

(KP-201C) or write settings from digital keypad to inverter.

(1) Store settings in digital keypad(KP-201C)

To disconnect digital keypad and press until that digital

keypad is connected to inverter, the LED of keypad will
display ' ' to indicate that the setting is storing in
digital keypad (KP-201C).

(2)

Write setting from digital keypad(KP-201C) to inverter

To disconnect digital keypad and press until that digital

keypad is connected to inverter, the LED of keypad will

display ' ' to indicate that the setting is writing from

digital keypad (KP-201C) to inverter.

(3)

If the inverters have different software versions, they can not

read /write setting to inverter each other. The

digital keypad

(KP-201C) display will show the '

b. Resume factory settings

(1) To disconnect digital keypad (KP-201C) and press

until that digital keypad is connected to inverter, the LED of
keypad will display ' ' to

indicate that resume the

factory settings of 60HZ.

(2) To disconnect digital keypad (KP-201C) and press

until that digital keypad is connected to inverter, the LED of
keypad will display ' ' to indicate that resume the
factory settings of 50HZ.

c. Resume last settings

To disconnect digital keypad (KP-201C) and press until

that digital keypad is connected to inverter, the LED of keypad
will display ' ' to indicate that the last settings have been
resumed.

S T O P

R E S E T

PROG

F U N

D A T A

Содержание RM5G









































































































Результаты поиска

Содержание RM5G

Отзывы:

Похожие инструкции для RM5G

Бренды по названию

Популярные бренды

Rhymebus RM5G, Руководство пользователя

Результаты поиска

Содержание RM5G

Отзывы:

Похожие инструкции для RM5G

Бренды по названию

Популярные бренды