Paradyne 7110 Скачать руководство пользователя

Страница: 118 / 167

MIB Descriptions

C-7

7110-A2-GB20-00

June 1997

Table C-2.

Interfaces Group Objects (4 of 5)

Object, OID, Access

Setting/Contents

Description

ifOperStatus

( ifEntry 8 )

1.3.6.1.2.1.2.2.1.8
read-only

Specifies the current
operational state of the
interface.

Management port. When
configured as Net Link,
up(1) and down(2) are
based on the current state of
the link-layer protocol. When
configured for Alarms, the
interface is always up(1).
Never in testing(3) state.

Terminal port. Always up(1);
never in testing(3) state.

User Data Port

– up(1) – Port is assigned

(cross connected) to a T1
interface and both CTS
and DSR are ON

– down(2) – Port is

unassigned or either CTS
or DSR are OFF

– testing(3) – Test active

Network T1 Interface

– up(1) – No alarms

– down(2) – Alarms

– testing(3) – Test active

Facility Data Link (FDL).
When enabled, up and down
are based on the current
state of the physical and link
layer protocols.

– up(1) – Operational and

no active test on the
network T1 interface

– down(2) – Not

operational or disabled

– testing(3) – Test active

on network T1 interface

ifLastChange

( ifEntry 9 )

1.3.6.1.2.1.2.2.1.9
read-only

Indicates the amount of
time the interface has been
up and running.

Contains the value of
sysUpTime object at the time
the interface entered its current
operational state.

This object is only updated for
the up and down states; the
testing state is not mutually
exclusive with the up and down
states.

Содержание 7110


































































































































































Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды

Paradyne 7110, Руководство пользователя

Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды