Paradyne 7110 Скачать руководство пользователя

Страница: 42 / 167

Monitoring the DSU/CSU

4-10

7110-A2-GB20-00

June 1997

24-Hour Totals

The last two lines on the screen (above the dotted line) display the totals for each
statistic over the last 24 hours, along with the number of valid intervals included in
the total (up to 96).

Viewing DSU/CSU LEDs

The DSU/CSU LEDs can be viewed on the Display LEDs Status screen. This ATI
status screen is available locally and remotely.

The 12 LEDs are organized in three groups:

System LEDs display the status of the unit

Network LEDs provide the status of the network interface

Port LEDs display the activity on the user data (DTE) port

To view the LED status screen, follow this menu selection sequence:

Main Menu

→

Status

→

Display LEDs

main/status/leds

Device Name:

Model: 7110

DISPLAY LEDS

SYSTEM

NETWORK

PORT

OK FAIL TEST

SIG OOF ALM EER

TXD RXD RTS CTS DTR

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

ESC for previous menu

MainMenu

Exit

Refresh

ÎÎ

When viewed via the ATI, the status display screen is updated approximately
every 5 seconds. Use Refresh to obtain a current status of all LEDs.

Содержание 7110


































































































































































Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды

Paradyne 7110, Руководство пользователя

Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды