Paradyne 7110 Скачать руководство пользователя

Страница: 48 / 167

Testing

5-3

7110-A2-GB20-00

June 1997

Line Loopback

Line Loopback (LLB) loops the received signal on the network interface back to
the network without change.

Procedure

To run a Line loopback:

1. Position the cursor at the Start command next to Line Loopback on the

Network Tests screen.

2. Press Enter.

3. The Start command is changed to Stop. If you want to manually stop the test,

verify that the cursor is positioned at the Stop command.

4. Press Enter. The duration of the test is displayed.

496-15075

CSU

DSU

Network

Interface

ALL 1s

LLB

DTE

Line Loopback cannot be started when any of the following tests are already
active: Payload Loopback, Data Channel Loopback, Send Pattern test on the
network interface.

Содержание 7110


































































































































































Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды

Paradyne 7110, Руководство пользователя

Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды