Paradyne 7110 Скачать руководство пользователя

Страница: 36 / 167

Monitoring the DSU/CSU

4-4

7110-A2-GB20-00

June 1997

Table 4-2.

Health and Status Messages (2 of 2)

Message

What To Do

What Message Indicates

Network Mgmt
Link Down

This condition only occurs if
the Management port is
configured for Net Link, and
communication between the
management system and the
DSU/CSU is not currently
possible for the port.

1. Verify that the Management Port

Use configuration option is
properly set (see Appendix A for
configuration option information).

2. Check cables.

Device Fail
yyyyyyyy

An internal error has been
detected by the operating
software.

yyyyyyyy indicates

the 8-digit hexadecimal failure
code.

1. Provide the 8-digit failure code

shown (

yyyyyyyy ) to your service

representative.

2. Reset the DSU/CSU to clear the

condition and message.

Self-Test Results

The results of the last power-up or reset self-test appear in the middle column of
the System and Test Status screen.

Table 4-3.

Self-Test Results Messages

Message

What Message Indicates

What To Do

CPU Fail

The CPU failed internal testing.

1. Reset the unit and try again.

Device Fail

One or more of the DSU/CSU’s
integrated circuit chips has failed
device-level testing.

2. Call your service

representative for assistance.

B8ZS/LOS
Fail

The DSU/CSU failed to transmit all
ones or to detect a Loss of Signal.

Network T1
Fail

The DSU/CSU failed to internally
loop data on the network T1 circuit.

Alarm Fail

The DSU/CSU failed to transmit AIS
or to detect a Yellow alarm.

Memory Fail

The DSU/CSU failed memory
verification.

DSU/CSU
Port Fail

The Data Port failed self-test.

Failure
xxxxxxxx

An internal failure occurred.
(xxxxxxxx represents an eight-digit
hexadecimal failure code for use by
service personnel.)

Record the failure code and
contact your service
representative.

Passed

No problems were found during
power-up.

No action needed; no problems
were found during power-up or
reset.

Содержание 7110


































































































































































Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды

Paradyne 7110, Руководство пользователя

Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды