Paradyne 7110 Скачать руководство пользователя

Страница: 50 / 167

Testing

5-5

7110-A2-GB20-00

June 1997

Repeater Loopback

Repeater Loopback (RLB) loops the signal being sent from the data port back to
the data port. Framing CRCs and BPVs are corrected.

Procedure

To run a Repeater loopback:

1. Position the cursor at the Start command next to Repeater Loopback on the

Network Tests screen.

2. Press Enter.

3. The Start command is changed to Stop. If you want to manually stop the test,

verify that the cursor is positioned at the Stop command.

4. Press Enter. The duration of the test is displayed.

496-15077

CSU

DSU

Network

Interface

RLB

DTE

ALL 1s

Repeater Loopback cannot be started when any of the following tests are already
active: Data Terminal Loopback, Data Channel Loopback, Payload Loopback.

Содержание 7110


































































































































































Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды

Paradyne 7110, Руководство пользователя

Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды