Paradyne 7110 Скачать руководство пользователя | Manualshive

Страница: 70 / 167

background image

Security

7-5

7110-A2-GB20-00

June 1997

When user access to the ATI is attempted through the Terminal port or a Telnet
session, the ATI response is based on the Login Required option and the
availability of the ATI. Table 7-2 describes how the system responds to various
ATI access conditions.

Table 7-2.

ATI Access Conditions

I f access to the ATI
is through the . . .

Then . . .

What to do now?

Terminal port with
Security disabled with
the

Login Required

option

set to Disable

(See Table A-5)

The Main Menu screen
appears.

Select a menu option to begin your
session.

Terminal port with
Security enabled with
the

Login Required

option

set to Enable

(See Table A 5)

You are prompted for a
login ID and password.

If Invalid Password appears,
re-enter the password. After three
tries with an invalid password,
contact the system administrator.

(See Table A-5)

The Main Menu screen
appears if the login ID is
not configured yet.

Select a menu option to begin your
session.

Terminal port and the
ATI is already in use
with a Telnet session

User Interface Already
In Use

message appears

with the active user’s IP
address and Login ID.

Try again later. When the ATI is
available, the message User
Interface Idle

appears.

Telnet session and the
ATI is currently in use

Connection Failed
message appears. The
DSU/CSU allows only
one connection or active
interface at a time.

Try again later.

«
...
68
69
70
71
72
...
»

Содержание 7110








































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7110

AirPlus G DWL-G510

Бренд: D-Link Страницы: 12

Бренд: IFM Electronic Страницы: 6

Бренд: j5 create Страницы: 444

TravelCharge Companion HT 3.4

Бренд: Wagan Страницы: 16

Powerline PL1200

Бренд: NETGEAR Страницы: 12

Бренд: Macally Страницы: 14

Бренд: Atlantis Страницы: 24

Бренд: Emerson Страницы: 8

Rosemount Smart Wireless THUM

Бренд: Emerson Страницы: 60

Бренд: Tripp Lite Страницы: 25

Twin USB Sockets Cupholder Adapter

Бренд: Wagan Страницы: 7

Бренд: Erbe Страницы: 84

Бренд: Devolo Страницы: 32

dLAN 500 AVsmart+

Бренд: Devolo Страницы: 35

Бренд: Allen-Bradley Страницы: 12

Baseus C-C3UEHVMSDC35

Бренд: ALZA Страницы: 46

Бренд: Mitel Страницы: 21

Бренд: Mitel Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды