Paradyne 7110 Скачать руководство пользователя | Manualshive

Страница: 122 / 167

background image

MIB Descriptions

C-11

7110-A2-GB20-00

June 1997

IP Group

The Internet Protocol Group objects are supported by the unit for all data paths
that are currently configured to carry IP data to/from the unit. All of the objects in
the IP Group, except for the IP Address Translation table, are fully supported.
The following table provides clarification for objects contained in the IP group
when it is not clear how the object definition in MIB II is supported by the unit.

Table C-5.

IP Group Objects (1 of 3)

Object, OID, Access

Description

Setting/Contents

ipForwarding

(ip1)

1.3.6.1.2.1.4.1
read-write

Specifies whether the unit
is acting as an IP gateway
for forwarding of datagram
received by, but not
addressed to, the unit.

Supports only the following
value:

forwarding(1) – The unit is
acting as a gateway.

ipAddrTable

(ip20)

1.3.6.1.2.1.4.20
read-only

The address table.

Supported.

ipAdEntAddr
(ipAddrEntry 1)

1.3.6.1.2.1.4.20.1.1
read-only

An IP address supported by
the unit which serves as an
index to the address table.

Indexes for tables must be
unique. Therefore, only one
ifIndex can be displayed for each
IP address supported by the
device. If the same IP address is
configured for multiple interfaces,
or for default IP addresses, the
ipAddrTable will not display all of
the interfaces that support a
particular IP address.

ipAdEntIfIndex
(ipAddrEntry 2)

1.3.6.1.2.1.4.20.1.2
read-only

If this object has a greater
value than the ifNumber,
then it refers to a
proprietary interface not
currently implemented by
the MIB II Interface Group.

None

«
...
120
121
122
123
124
...
»

Содержание 7110








































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7110

Бренд: FastTt Страницы: 5

Бренд: NetComm Страницы: 6

Бренд: Mercusys Страницы: 59

Бренд: Pepperl+Fuchs Страницы: 25

Cheetah Wireless-3501C

Бренд: Accton Technology Страницы: 50

Бренд: I-GO Страницы: 2

Бренд: Acard Страницы: 35

Бренд: Bose Страницы: 2

DUAL-BAND Wi-Fi

Бренд: Belkin Страницы: 38

Бренд: MAHLE Страницы: 10

Бренд: Shimano Страницы: 24

AirStation WLI-USB-KB11

Бренд: Buffalo Страницы: 45

Бренд: Abocom Страницы: 17

Бренд: DEWESOFT Страницы: 14

Бренд: Flying Voice Страницы: 46

LT30 - XGA DLP Projector

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 7

Бренд: NEC Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды