Paradyne 7110 Скачать руководство пользователя

Страница: 57 / 167

Testing

5-12

7110-A2-GB20-00

June 1997

Send FT1 Up/Down Sequences

The local DSU/CSU can send an ANSI T1.403 (Annex B) Up or Down sequence
to request the start or stop of a Data Channel Loopback on a remote DSU/CSU.

The DSU/CSU can send:

In-band ANSI T1.403 (Annex B) Up (activation) code to request the start of a
Data Channel Loopback at the remote DSU/CSUs or

In-band ANSI T1.403 (Annex B) Down (deactivation) code to request
termination of a Remote Data Channel Loopback at the remote DSU/CSU.

Procedure

To send a FT1 Up or Down sequence to a remote unit:

1. Position the cursor at the Up or Down selection next to Send FT1 Loopback

on the Data Port Tests screen.

2. Press the space bar to select the desired code (Up or Down).

3. Position the cursor at the Start command next to Send FT1 Loopback on the

Data Port Tests screen.

4. Press Enter.

5. The Start command is changed to Sending. The Up or Down sequence

transmission stops automatically after 10 seconds. You cannot stop the
sequence manually.

The Send FT1 Up/Down test cannot be started when any loopback or Send
Pattern test is active on the network interface.

Содержание 7110


































































































































































Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды

Paradyne 7110, Руководство пользователя

Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды