Paradyne 7110 Скачать руководство пользователя

Страница: 78 / 167

Configuration Option Tables

A-3

7110-A2-GB20-00

June 1997

System Options Menu

For System Options, refer to Table A-1. To access the System Options screen,
follow this menu selection sequence:

Main Menu

→

Configuration

→

Load Configuration From

→

System

Table A-1.

System Options

Self Test

Possible Settings: Enable, Disable
Default Setting: Enable

Controls whether or not the DSU/CSU performs a self-test at power-up and after reset.

Enable – Self-test will be performed at power-up and after a reset.

Disable – Self-test is disabled. The DSU/CSU will still perform a few basic tests (such
as memory and program checksum).

Test Timeout

Possible Settings: Enable, Disable
Default Setting: Enable

Allows user-initiated tests to end automatically. Recommend enabling when the unit is
managed remotely through the FDL to avoid the requirement to terminate the test
manually.

Enable – User-initiated loopback and pattern tests end when test duration is reached.

Disable – Tests can be terminated manually from the Network Tests screen. Refer to
the

Running Network Tests

section of Chapter 5.

NOTE:

Tests commanded by the DTE or network-initiated tests are not affected by
this test timeout.

Test Duration (min)

Possible Settings: 1–120
Default Setting: 10

Number of minutes for a test to be active before automatically ending.

Test Duration (min) option appears when Test Timeout is enabled.

1 to 120 – Amount of time in minutes for a user-initiated test to run before terminating.

Security Violation Alarm

Possible Settings: Enable, Disable
Default Setting: Enable

Issues an alarm when access to the unit is attempted and fails.

Enable – Alarm generated when a security violation is detected. Refer to the

Trap: authentificationFailure

section of Appendix D for possible alarm causes.

Disable – No alarm generated for a security violation.

Содержание 7110


































































































































































Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды

Paradyne 7110, Руководство пользователя

Результаты поиска

Содержание 7110

Отзывы:

Похожие инструкции для 7110

Бренды по названию

Популярные бренды